Oak Bluffs, MA old classifieds archive and funnies > Ads By members
> Tamagawa dc servo drive tdm driver AU3610N200 year 2002
Tamagawa dc servo drive tdm driver AU3610N200 year 2002
***Pictures show 3 unit but Price for only one unit***
Please select only two result that viewed table, I will service only "International EMS-Package" and "International Parcel-Air" EMS also faster!
Learn more about EMS or Parcel-Air service follow these
http:// /product_servicedetail_en.asp?cat_id=5&product_id=44-S-000017
and http:// /product_servicedetail_en.asp?cat_id=6&product_id=44-S-000005
DC Servo Driver TAMAKAWA for General DC Servo motor !!!
JAPAN Servo Driver in good conditions (95% beauty and clean)
Connected and Power ON Tested with Standard usage instruments, Fine-Tunning for ready to use with general DC Servo motor.
Controller PCB and TR Power look clear and clean, not burning or un authorized modified.
Seen No repair or parts replacement before, Product in year 2002.
Standard midium Drive size, Easy to installations with holder mount ears.
Easy wires connection with special terminal at left side of Driver (sell in cluded) or direct wirring to Driver interface Connecters.
Safety with NFB No-fuse Breaker (resetable) and Driver protection circuit with alarm LEDs display.
This Driver get the best closed loop control, I tested.
Motor shaft very hard-lock when enable this driver with no speed reference signal (0Volt Vref.) Its brake the shaft for hold the position stand-still (after I compleated tunning the "OFFSET" VR.)
You can also adjust others setting VRs for tne better running of the Driver.
- CURRENT (Max Current Limitter for Output to Motor)
- ZERO (OFFSET Drive Stand-Still)
Available LEDs to monitor Driver status
- AL O.S (Over Speed - Tacho Loss)
- AL O.L (Over Load - Output Current Limited)
- AL NFB (Over Current Input - Short circuit -No fuse Breaker tripped)
- AL TMP (Over temperature of Driver - Power output Transistor stage - heat sink hot)
You can easy start up to operate this Driver only connect follow these-
1) Connect 100-120 Volt AC Input supply to Driver (use only single phase two wires power with ground for safety)
2) -10V to +10V Speed Reference signal input to Driver for Fast/Slow CW or CCW rotation (Shielded cable)
3) Output to DC Servo Motor 200-250 Watt (I tested) two wires
4) Feedbak input from DC Servo Motor's Tacho Generator +-10V per 1000rpm (or +-6V to 10V can use) two wires (Shielded cable)
5) Enable this Driver only contact two wires for ON/OFF Servo loop (Motor shaft free-run or under control)
6) If Driver healthly will contacted it self with two wire NO/NC for external use to monitor this Driver OK or Not ready.
This board conditions is good in 90-95% looks and also working in last time before kept in stock, I tested on the real operating machine.
Any trimpot(VR) or adjustment points or calibration points still in same of it old possitions or marked from originl Pcb. maker factory!
Any DIP switches setting, toggle switches or all of electronics component on this board is original, not seen the repair or replacement crack in over all of this board!
No wire jumper for un authorized modify, no Pcb. copper trace cutting or corrupt of pads -donuts -trace or solder-desolder ruts. It have only the board revision modified from original Pcb.maker factory!
Any sockets or connectors on this board also was looked clearly, not broken, connectors pins not bend, no much more rust or dirt oxide!
Any electro-mechanical ont this Pcb. for exem- the relays was still in its old place, no replacement with other board, no changed before, It was original code. Even the fuses it was old items!!
On this board, It also have the original Pcb.name and Pcb.code and Pcb.serial number even of the QC sticker still at its placed!
The component on this board also have some of hard-to-find parts, some module, some HIC, some make for oem. oder only parts.
Need to view more pictures or more detail of this item or other similar items?, please send request to me develop1@asianet.co.th
Please understand my little notice follow this-
It meaning you will be transfer your money to my bank account in THAILAND.
This bank branch in BANGKOK the metropolis.
My bank account was continuously used more than 14 years adged.
Our Thailand currency in THAIBAHT (BAHT)
If you not sure about total price or any question please contact me at develop1@asianet.co.th (It's my permanently email and directly to me)
Need my Bank info for money transfer purpose? please send request via email.
